Skip to content
BusPart Korea

How we grade used parts

Every part is removed, tested and graded in Korea before export. The grade and the test record are on every listing.

  • ATested
    Wear
    None or very light
    Tests
    Passed every test
    Good for
    Main fleet and long routes
  • BGood
    Wear
    Light, on the surface
    Tests
    Passed every test
    Good for
    Daily city routes
  • CUsable
    Wear
    Visible, does not affect use
    Tests
    Works as it should
    Good for
    Spare stock and budget repairs

What we test

The tests depend on the part. These are the checks behind each grade.

Brakes 12
Output test
9.5 bar in 4 min
Visual check
No oil leaks
Valve check
Opens at 10.0 bar
Drying test
Dew point within spec
Leak test
No air leaks
Stroke test
Push rod stroke 52 mm
Diameter measured
Ø 411.2 mm, within limit
Crack check
No cracks
Runout measured
0.15 mm, within spec
Lining measured
11.5 mm left of 14 mm
Pressure test
Held 8.0 bar for 10 min
Piston measured
Ø 60.0 mm, within spec
Electrical 7
Output test
148 A at 2,500 rpm
Visual check
Visible wear on housing
Bearing check
Light noise, within limit
Load test
Cranks at 24 V
Brush check
Brushes within limit
Lamp test
Low and high beam work
Lens check
Light haze, no cracks
Engine 11
Shaft play
Axial 0.06 mm, within limit
Visual check
No oil on the turbine side
Boost test
Reached target boost
Leak test
No leaks at 1.5 bar
Bearing check
Turns smoothly, no noise
Pressure test
No leaks at 1.4 bar
Flow test
Flow within spec
Spray test
Even spray pattern
Seal check
Seals replaced
Flatness measured
0.05 mm, within spec
Fan test
Engages at 85 °C
Transmission 18
Pressure test
Held pressure for 5 min
Visual check
Light wear on the push rod
Bore measured
Ø 22.2 mm, within spec
Thickness measured
Lining 3.1 mm above rivets
Spline check
No wear steps
Runout measured
0.3 mm, within spec
Load test
Clamp load within spec
Flatness measured
0.1 mm, within spec
Shift test
All gears engage on the bench
Noise test
No grinding
Leak test
No oil leaks
Gear check
No chipped teeth
Joint check
No play in the U-joints
Balance check
Balanced
Stroke test
Full stroke, smooth return
Free play measured
4 mm, within spec
Bushing check
Bushings replaced
Bearing check
Turns smoothly
Air conditioning 5
Pressure test
Reached working pressure
Clutch check
Engages at 24 V
Visual check
No oil leaks
Noise test
Light noise, within limit
Fan test
Both fans run
Chassis 12
Camber measured
Within spec
Visual check
Surface rust, no cracks
Bushing check
Worn, replace on fitting
Leak test
No leaks at 8 bar
Crack check
Piston intact
Damping test
Damping force within spec
Pressure test
Relief at 150 bar
Noise test
No whine
Backlash measured
Within spec at centre
Gear check
Even contact pattern
Bearing check
Turns smoothly, no play
Runout measured
0.05 mm, within spec
TestExample result
Output test9.5 bar in 4 min
Visual checkNo oil leaks
Valve checkOpens at 10.0 bar
Drying testDew point within spec
Leak testNo air leaks
Stroke testPush rod stroke 52 mm
Diameter measuredØ 411.2 mm, within limit
Crack checkNo cracks
Runout measured0.15 mm, within spec
Lining measured11.5 mm left of 14 mm
Pressure testHeld 8.0 bar for 10 min
Piston measuredØ 60.0 mm, within spec

A test record on every listing

Each part page shows the tests it passed, with the date and the place.

Measuring a part with a vernier caliper
ATestedAir compressor

58210-8A000

  • Output test9.5 bar in 4 min
  • Visual checkNo oil leaks
  • Valve checkOpens at 10.0 bar
Tested 25 Oct 2026 · BusanSee this part

Find a part with its grade